Doosan PUMA 400 Turning center

DOOSAN PUMA 400
Powerful, Heavy Duty Turning Center

PUMA 400
The PUMA 400 seríes turníng centers are without a doubt the most powerful machínes in their class.
High metal removal rates, along with rapíd positíoníng and fast bí-directional turret indexíng, guarantee unmatched cycІe times when real cutting is essential.
Massive yet responsíve turning centers wíthout compromíse. The most powerful machínes in their class.
Main Spindle
The headstock castíng ís made of Meehanite and ríbbed on the outside to increase the surface area for better heat dissípatíon. The headstock and main spindle are manu-factured ín a temperature controlled envíronment then assembled and tested in our clean room. Double row of cylindrical roller bearíngs and duplex angular contact bearíngs, P4 class of the spíndle ensure the híghest rigidíty and efficiency to transmit motor power to the end.
Max. spindle speed
Motor 30 mín
Main Spíndle Dríve
Precí-Flex adapterapplícation
Spindle speed r/min

 

The high-torque spindle motor provides power for heavy stock removal, greatly reducing the number of roughing passes required. For 3-axis milling models, the motor is a spindle servo type controlling both the spindle in 2-axis mode and full contouring C-axis in the 3-axis mode. Switching between the two modes is nearly instantaneous.
Isolated Gear Box D1 Gear Box
Power is delivered to the spindle through a two-speed gearbox allowing high spindle speeds as well as powerful low-end torque. The gearbox and spindle motor are isolated from the spindle, eliminating transfer of heat and vibration.

PUMA 400 AJB/CjLA/LBILCjXLAI XLB/XLC
BF Gear Box
Heavy cutting is enabled with a 2-step Baruffaldi Gearbox standard, which is equipped with double bearings at the pulley shaft to enhance durability. The high precision BF Gearbox reduces noise at high speed. The gearbox and motor are separated from the spindle to isolate vibration, further enhancing working accuracy.
PUMA 400Mc/LMC/XLMc
PUMA 400A/LA/XLA/B/LB/XLB/CLSC/MA/LMA/XLMA/MV/LMB/XLMV

Fast Turret Indexing
The large 12- and 10-station heavy-duty turret features a large diameter Curvic coupling and hydraulic clamp force. The heavy-duty design provides unsurpassed rigidity for heavy stock removal, fine surface finishes, long boring bar overhang ratios, and extended tool life. Turret rotation, deceleration, and clamp are all controlled by a reliable high-torque hydraulic index motor. Unclamp and rotation are virtually simultaneous. Turret indexing is non-stop bidirectional with a second next station index time. Turning tools are securely attached to the turret by wedge clamps.
Index time: 1-station swivel
Number of tool stations:
12 stations
In the case of PUMA 400 B/C: 10 stations

 

BMT Milling Turret
The 12-tool stations turret BMT55P makes it possible to complete complicated parts requiring many tools in just one setup. Reliable servo-driven turrets reduce the total cycle time required to machine parts.

Straight Milling Head
Angled Milling Head

Bed and Way Construction
Doosan Infracore precision machine tools are internationally known for their durability, rigidity, and high accuracy. Only well-proven and time-tested manufacturing techniques can produce machines of this quality.
The PUMA 400 series is a true 45-degree slant bed design. The bed is a one-piece casting with both the saddle and tailstock guideways in the same plane to eliminate thermal distortion. The heavily ribbed torque tube design prevents twisting and deformation. Fine grain Meehanite processed cast iron is used because of its excellent damping characteristics. This ensures high rigidity with no deformation during heavy cutting. The slant angle allows for easy loading, changing, and inspection of tools. All guideways are wide wrap-around rectangular type for unsurpassed long-term rigidity and accuracy. The guideways are widely spaced to ensure stability and are fully protected. Each guideway is induction hardened and precision ground. A fluoroplastic resin, Rulon 142, is bonded to the mating way surfaces for its wear and friction characteristics and then hand scraped for a perfect fit and center height. Optional long bed enables extra-long shaft machining.

Rapid Traverse
X-axis: 16 m/min (ipm)
Z-axis: 20 m/min (ipm)
PUMA 400A/B/C/MA/MV/MC Scraping of Slideway
Outstanding rigidity for high feedrates: 1 m/min (ipm)
PUMA 400LA/LB/LC/LMA/LMV/LMC
10 m/min (ipm), PUMA 400XLA/XLB/XLC/XLMA/XLMV/XLMC

Ergonomic Design
Double-Paneled Safety Window
Operator’s Panel
The operator's safety can be enhanced through the front door with its shock-absorbing laminated glass and double panel construction. The windows without grating also provide a clear view of the machine inside. The accessibility during setup and operation is improved. The layout and location of the panel are ergonomically designed to be efficient and convenient for the operator.

Tempered glass and metal plates are provided for diagnostics of the machine, control, and programming errors.
Outside: Polycarbonate.

 

Precí-Flex Ready Rotary Tools Rotary Tool Power-Torque Diagram
PUMA 400M / 400LM / 400XLM
Precí-Flex ready rotary tool holders are available on the milling versions. Precí-Flex is a tooling system that utilizes the existing ER collet taper in the rotary holders. The spindle face is precision ground relative to the taper, and there are four drilled and tapped holders in this face. The Precí-Flex adapters locate on both the taper and the spindle face for maximum rigidity.

 

Axis Drive Construction and Tailstock

Double Pretensioned Ball Screw
Both the X and Z axes feature a double pretensioned ball screw, supported on each end by precision-class P4 angular contact thrust bearings and precision Morse Taper 61 live center bearings. These components provide outstanding rigidity. The 120mm (4.7-inch) diameter high-precision ball quill stroke is activated either by the program or foot switch. Auto lubrication is provided to the quill and guideways.

Programmable Tailstock
The programmable tailstock body is mounted on the same guideway surface as the headstock. The tailstock provides additional support during machining and is easily adjustable through program controls.

Axis Drives
Each axis is powered by a maintenance-free digital AC servo motor. These high-torque drive motors are connected to the ball screws without intermediate gears for quiet and responsive slide movement with virtually no backlash.

Collection of Waste Lubrication Oil & No Coolant Leakage
Less waste lubrication oil extends the lifetime of the coolant and reduces grime and the offensive smell inside the machine. The machine covers are rigorously designed, manufactured, and tested to ensure that no coolant leakage occurs in any condition. The factory always ensures that the environment remains clean.The temperature of the hydraulic oil is regulated by a cooling system. The coolant is kept clean, and its life is extended with bed casting channels from the Z-axis to a separate reservoir. A belt oil skimmer picks up and removes waste oil from the coolant tank, which is easily drained.

Automatic lubrication is provided to all guideways, ball screws, and the tailstock quill. A maintenance-free piston distributor delivers a precise quantity of oil to each lubrication point. The reservoir lasts up to 80 hours. A low-level alarm prevents the machine from restarting without lubricant.Each axis ball screw is protected by electric torque limiters to minimize damage in the event of a crash. Upon impact, the limiter immediately stops the machine.

The high-pressure coolant flushes chips out of drilled holes, reduces the need for peck drilling cycles, meets the requirements of most insert drill manufacturers, and significantly increases tool life. The large, separate 280L (74-gallon) coolant tank and chip pan are isolated from the machine bed to prevent heat transfer and allow easy cleaning.The PUMA series offers an optional long bed that is ideal for machining longer shafts or larger components. The long boring bar holder is designed to provide stable support for extended tooling applications.The diagram of the spindle power and torque characteristics is included, showing the spindle's capabilities during various machining operations.

Tool Specifications

PUMA 400 M / LM / XLM Standard Tooling

Drill Sockets:

MTM2-H60 M7A4-H60

Milling Collets:

ER 40

Boring Bar:

Ø60

U-Drill Sleeves:

U-Drill 12st Turret

BMT 75P Milling Arbor Adapter

Tool Work Range

PUMA 400 / 400L / 400XL

Unit: mm | inch

OD Tool Holder: ID Tool Holder

PUMA 400: MAO.001

PUMA 400 I: QUILL TRAVEL

PUMA 400M / 400LM / 400XLM

OD/ID Tool Holder Straight, Milling Unit

Machine Specifications

PUMA 400A | PUMA 400B | PUMA 400C | PUMA 400XLA | PUMA 400LA | PUMA 400LB | PUMA 400LC | PUMA 400XLMA | PUMA 400LMA | PUMA 400LMB | PUMA 400LMC | PUMA 400XLB | PUMA 400XLC |

Coolant supply equipment

Additional tool holders and sleeves

Controller: Fanuc 31i-A

Foot switch

Air blast for chuck

Dual chucking pressure

Full enclosure chip and coolant shield

Air gun

Hardened ground jaws

Hand tool kit

Automatic door with safety device

Hydraulic steady rest

Hydraulic chuck actuating cylinder

Automatic measuring system

Manual steady rest

Hydraulic power unit

Oil skimmer

Leveling jack screw plates

Automatic power off

Live center

Bar feeder interface

Programmable tailstock

Chip bucket

Work light

Chip conveyor

Optional Features

Long boring bar Ø100

Soft jaws

Automatic work loading

Pressure switch for chucking

Lubrication equipment

Unloading equipment pressure check

 

NC Unit Specifications

Control and Programming Functions

Controlled Axes: The Doosan 32i-A and Fanuc 32i-A Series both control the X, Z, and C axes.

Simultaneous Control: The Doosan system operates in a 2-axis mode by default, while Fanuc allows control of 3 axes simultaneously.

Programming Type: Both systems offer conversational programming.

Maximum Program Dimensions: Both systems support 9-digit program dimensions.

Backlash Compensation: Backlash compensation can be adjusted from 0 to 9999 pulses on both systems.

Multi-repetitive Canned Cycle: Both systems support multi-repetitive canned cycles, with specific cycle codes ranging from G70 to G76.

Cs Contouring: Both systems provide Cs contouring capabilities.

Program Input System: Direct drawing of dimensions is supported in both systems.

Block Skip Function: This function is available as an optional feature on both systems.

Increment System: Both systems use a 1/10 increment system.

Sub Program Call: The Doosan system supports nesting up to 10 levels, while the Fanuc system supports nesting up to 4 levels.

Tape Format for FANUC: Both systems support the FANUC tape format.

Work Coordinate System: Both systems support work coordinate systems G52 through G59.

Stored Stroke Check: Both systems support stored stroke check functions (1 & 2).

Overtravel Control: Both systems provide overtravel control.


Tool Functions

Auto Tool Offset: Both systems provide automatic tool offset capabilities.

Manual Tool Return: The systems support manual tool return with the G28 code.

Tool Geometry/Wear Compensation: Both systems allow for tool geometry and wear compensation.

Automatic Operation Memory: Both systems offer automatic operation memory.

Buffer T-Code Function: The T2 function for tool codes is supported by both systems, with a 2-digit input.

Circular Interpolation: Circular interpolation (G02) is supported by both systems.

Tool Management System: Both systems include a tool management system.

Continuous Thread Cutting: Continuous thread cutting functionality is supported on both systems.

Dwell per Second: The G04 dwell command is available for both systems.

Tool Nose Compensation: Tool nose compensation is available.

Background Editing: Both systems offer background editing capabilities.

Search Function: Both systems provide a search function for programming.

Expanded Part Program Editing: Both systems support expanded part program editing.

Pocket Calculation and Tool Type Decimal Point Programming: Available in both systems for pocket calculations and precise tool programming.

Program Copy/Move: Both systems allow for the copying and moving of programs.


Program Length

The standard part program length may vary depending on the export condition.

With optional functions added, the program length can be reduced.

 

The original leaflets are for sale. A preview is shown. The price of the leaflet is on request.