Ercolina TB 60 topbender

ERCOLINA TOP BENDER TB60 Including: Art. TB60-V2T, Art. 050A-050B-050D/1-050G-050H-810-FPO10

Wide bending radius range from R10 to R380 mm

Minimum tube diameter 5 mm, see table for max. capacity

Maximum bending angle 180 degrees

2-speed operation (rpm and rpm approx.)

Bend angle and springback angle are programmable by the microprocessor

10 programs of 9 bends each can be memorized, with battery backup memory

Microprocessor has an easy-to-use soft-touch keyboard, can be set to different languages

Machine fault diagnosis functions

Can be fitted with optional 2-axis positioner Art. A40/P to produce a repeatable sequence of curves in different planes

Rapid tool change former and counterbending die in 30 seconds due to quick-change counterbending die system and hexagonal center drive socket on formers

Rapid engagement and disengagement of the counterbending die

Easily movable by means of wheels incorporated into the rear of the machine structure

Size: 760 x 500 x 1000 mm (30 x 20 x 39)

Weight: 170 kg (374 lbs) machine body only

Available voltages three-phase: 230-400-480-580V 50/60 Hz - Specify voltage required

THREE-PHASE VOLTAGE SUPPLY MAXIMUM BENDING CAPACITY FROM Ø 6 mm to Ø 60 mm WITH MINIMUM RADIUS TWICE THE TUBE O DEPENDING ON TYPE OF TUBE, O WALL THICKNESS Section Material Max Ø x Max Ø x Wall thickness mm, inches O Boiler tubes 60 x 4 (2) O Standard steel tubes 60 x 4 (2.5) O Soft brass 60 x 6 O Stainless steel 60 x 3 (18) O Welded tube for furniture 60 x 4

KIT: consists of O Hydraulic tube ST35. 64 x 5 x machine with 6 formers and counter O Hydraulic stainless steel tube 304 64 x 3 x bending dies as supplied with the O Hard copper aluminum 64 x 6 Art. OK 50 Top Bender machine Mild steel 35 see catalogue. Mild steel 12 x 125 x 5 i Mild steel 30 x 60 x 3 x Art KIT: consists of Mild steel 60 x 60 x 3 machine with 6 formers and counter Mild steel 30 x 30 x 3 bending dies as supplied with the F- Mild steel 60 x 60 x 6 Art. OK 50 Top Bender machine, [ Mild steel 50 x 25 x 5 (2 x 2 x with bending radius approx. 30. sε π ε м вRε 2 0 0 ı

ERCOLINA TOP BENDER 050 Including: Art. 050A-050B-050D/1-050G-050H-810-FPO10

Bending radius range from R10 to R300

Two bending speeds, and rpm 50 Hz

CONTROLS: electronic microprocessor with backup battery for memory storage

Capable of programming 90 bending angles divided into 10 program blocks of 9 bends each

Ercoline TB 60 top bender Display and control of C axis bending angle 

Display and control of X axis millimetric control of slider position

A1 information can be displayed in many languages

MOTOR: 2-speed 1750W - Three-phase 2/4 pole

Auto-braking and mechanical safety device

Power supply 200-240 / 380-440 / 480 500 / 600 Volt 50-60 Hz - important detail to specify when ordering

Emergency stop button

Speeds: low and high speed to optimize work times

Flashing lights signaling overload machine stop

Low voltage control circuit 5 Volts

Phase inverter

DIMENSIONS: 

WEIGHT: 130.60 lbs only base unit

CONSTRUCTION CHARACTERISTICS: Upper body part in aluminum alloy

Lower body part is a welded steel fabrication

WHEN ORDERING SPECIFY VOLTAGE Art. OK50ε TOP BENDER KIT complete with: minimum radius twice the tube O Art. 050: 1 Top Bender with standard accessories Art. 050A-050B-O50D/1- Section Material Max Ø x Wall Max O x Wall thickness mm inches Art. 151: 6 standard formers R46-R56- gas x groove Ø Standard steel tubes 60 x 4 (23/8 x must be specified only from those 1 Soft brass 60 x 4 (23/8 x according to tables 1 and 3. Stainless steel 60 x 23/8 x Art. 152: 6 standard counterbending Hydraulic stainless steel ST35 60 x 4 (23/8 x dies. Select groove diameters matching Hydraulic 304L stainless steel ІuЬ 64 x 3 (21/2 x 18 the formers and only those available for Hard copper aluminum 64 x 4 (21/2 x 154 and Art. 155 Mild steel 35

Mi1d steel 10 x 60 3/8 x 23/8 Top Bender Kit as OK50 Extended Top Bender on request for max 60, radii from Mi1d steel SETTEMBRE .

ERCOLINA SUPER BENDER SINGLE PHASE DIGITAL Art. 060A and Art. 060B WITH STANDARD ACCESSORIES INCLUDING: Art. 050A-050B-050D/1-050G-O50H-810-FPO10 The SUPER BENDER A and B have a lower maximum capacity than the Top Bender, they do not have a microprocessor controller but have a lower cost. See the details below.

Bending radius range from R10 to R300

Bending speed rpm model 060A, 50Hz or rpm 060B, 50Hz.

CONTROL; constant speed control and bending angle control to guarantee excellent bending angle repeatability and precision. One bending angle and one spring back angle can be programmed by means of a simple dial setting - extremely simple and easy to use

MOTOR: single phase. Double insulation to EEC standards 100/120 V - 200/220 V - 1760W 50-60 Hz

Bending angle regulation

Electronic braking system

Overload device with flashing light machine stop

Low voltage control circuit 24 Volts

DIMENSIONS: 

WEIGHT: 85 Kg. 189 Lbs. Approx.

CONSTRUCTION CHARACTERISTICS: Upper body part in aluminum alloy. Lower body part is a welded steel fabrication WHEN ORDERING PLEASE SPECIFY VOLTAGE MAXIMUM BENDING CAPACITY FROM Ø 5 mm to Ø 48 mm. MINIMUM BENDING RADIUS TWICE THE TUBE Ø Section Material Max wall thickness mm Max O x wall thickness inches SUPER BENDER SUPER BENDER SUPER BENDER A U BENDER Boiler steel tubes 48 x 42 x 11/2 gas x 11/4 gas x Stainless steel tubes  Hydraulic 4L stainless steel tube ERCOLINA SUPER BENDER A capacity from 5 mm to 48 x mm., with standard accessories Art. 050A-050B-050D/1 -050G-050H-810-FPO10. ERCOLINA SUPER BENDER A capacity from Ø 5 mm to Ø 42 x mm., with standard accessories Art. 050A-0506-050D/1-050G-O50H-810-FP010. ERCOLINA SUPER BENDER A K1T capacity from Ø 5 mm to Ø 48 x mm., including: Art. 060A: 1 Super Bender version A with standard accessories Art. 050A-0506-050D/1 -050G-050H-810-FPO10. 5 standard formers R46-R56-R67-R90-R100 mm. The groove Ø must be selected from those indicated in tables 1-2-3-4. 5 standard counterbending dies. Select groove diameters matching the formers and only from those available for For sizes in inches and An ERCOLINA SUPER BENDER B K1T capacity from Ø 5 mm to Ø 42 x mm., including: Art. 060B: 1 Super Bender version B with standard accessories Art. O50A-050B-050D/1-050G-050H-810-FPO10. 4 standard formers R46-R56-R67-R90 mm. The groove Ø must be selected from those indicated in tables 1-2-3-4. Art. 152: 4 standard counterbending dies Select groove diameters matching formers and only from those available for For sizes in inches and