Gasparini co hydraulic shears

Gasparini co hydraulic shears

Technical Innovations For a New Way of Solving Your Shearing Problems Shear Model CO 10020 10,000 by ZO mm. capacity RAKE ANGLE ADJUSTMENT Can be adjusted rapidly by turning the selector to the desired angle which will depend on the plate thickness and then depressing the red pushbutton. The top blade adjusts itself automatically. Advantage: distortion-free cutting of narrow strips. STANDARD CONTROL PANEL - CONTROL PANEL ON EYE  CONSOLE COMPLETE AUTOMATIC CONTROL OF Rake angle Cutting length CONTROL PANEL Blade gap COMPLETE WITH Back gauge ELECTRONIC POSITIONER

Number of pieces

Auxiliary functions NEW DESIGN BLADE- QUALITY COMPONENTS CARRYING BEAM Most traditional shears use a Gasparini uses only top quality badly designed top beam. It is brands for the electric and usually too heavy and not electronic components in their aligned with respect to the machines Siemens and cylinders. The Gasparini shear Telemecanique. Components uses a top beam perfectly conform to current safety balanced between axis and standards. Safety and reliability cylinders, resulting in an guaranteed. excellent cut and guaranteeing extended blade and cylinder life. NEW RETRACTABLE BACK THREE WORK CYCLES GAUGE - The back gauges in the CO Free, Automatic and Inching. shear series are mounted The cutting command may be directly to the shear structure. given either by a pushbutton It does not undergo vibration on the control panel, or by during cutting as only the remote footswitch. The blade blade-carrying beam may be stopped and restarted descends. A special during cutting. mechanical device permits the back gauge to retract during cutting. This lets the blank fall freely. BACK GAUGE A manual or pneumatic device will lift the back gauge out of the way if you need to cut an occasional piece longer than the backstop and if your plates are thick enough to be rigid. Optional. MOD. CO 6020 Complete with the following optional accessories:

pneumatic sheet support with double movement

scrap box

light-guard system

slide for blanks ACCESSORIES The Gasparini standard shears already include accessories that permit you to start producing immediately. A vast range of optional accessories help you personalize your shear for particular needs. Our technical staff will be happy to help you find the right solution to your production problems. safety devices on the controls SLOW LINE CUTTING GUIDING and work cycles further protect the operator in the The shears are equipped with case of human error. Mark your plates and use the safety guards that conform to side support for extra lengths. those standards requested by the end-users country. Built-in CUTTING EDGE PROTECTED A special device on the shear bench lifts the sheet during feeding to avoid ruining the cutting edge of the blades. Any length of cut may be chosen. Adjustment is done rapidly and simply with a handwheel see photo . Advantage: saves valuable production time by increasing stroke speed. see photo . Precision guaranteed. BLADE GAP ADJUSTMENT For a good square, burr-free cut and for increased blade life, the blade gap must be suitably adjusted according to plate thickness. Adjustment is rapid and simple and is done with the handwheel which can be motorized on request Table representing the technical characteristics of our standard range. We produce special machines upon request to meet particular needs. serie CO 3 serie CO 4 serie CO 6 serie CO 8 The models marked by an asterisk need a pit foundation for the front bottom beam. SHEARING CENTRE FROM THE COS SERIES SHEAR BENCH - FRONT SUPPORTS A smooth steel table is suitable for the smaller model shears, while for the bigger models a bar type bench is advisable. Besides the standard front support arms provided with the shears, the following are also available: protractor arms, support arms ruled in millimeters and complete with references with micrometer adjustments. longer squaring arms, ball tables. MOD. CO 3025 MODEL CO 4020 Complete with belt conveyor, stacking unit. anti-scratch device, scrap box. The hold-down pressure is automatically controlled by the cutting pressure. The finger guard allows safe access, close to the blades, when cutting narrow strips. MODULAR SHEARING The CO shears are built in a way to facilitate retrofitting upgrade units such as:

Pneumatic sheet supports with double movement and automatic return of sheared piece to front bench

Anti-twist device for narrow strips in thick plate

Belt and chain conveyors

Anti-scratch device

Fully automatic stacking unit. MOD. CO 2530 Complete with chain conveyor and scrap box. MOD. CO 2004 MOD. CO 3006 WIDE RANGE A wide range of models are available, starting from the CO3 3 mm. series suited to cutting lightweight material, up to the CO20 20 mm. and CO30 30 mm. series for thick heavy-duty plates. A vast number of accessories completes the range. AUTOMATIC DESTACKERS AND Available in many versions for small, medium, and thick plate, they are numerically controlled for full automation. serie serie CO 10 serie CO 12 serie CO 16 serie CO 20 serie CO 25 supervisory programming SHEARING CENTRE over all operations of RIGHT-ANGLED SHEARS. the whole plant

Automatic feeding of NEW MODEL RIGHT-ANGLED different-sized pieces - SHEAR. CUTS OUT BLANK IN conveyed and stacked ONE STROKE. depending on blank

Blanks sorted out to dimensions. appropriate stacking stations automatically

Movements controlled and visualized

The DNC provides - SHEARING LINE FROM THE LT CO SERIES BRAKES SHEARS RING LINES motive purposes only. PRESS BRAKES IN TANDEM - CM 3 They may undergo variations Synchronized press brakes in should the manufacturer desire tandem. to make any modifications or COMPLEMENTARY improvements to the EQUIPMENT equipment.

Front feeders

Conveying units

Stacking units

Back gauges controlled by CNC with or without video graphics.