Hugh smith onbekend vertical bending machine 1

Hugh smith 

PREFACE WHY THE VERTICAL MACHINE IS BETTER THAN HORIZONTAL ROLLING EXAMPLES OF WORK DONE PLATE BENDING CAPACITY OF THE RANGE OF MACHINES NOTES ON CAPACITY TABLES INTRODUCTION TO THE USE OF VERTICAL BENDING MACHINES BENDING TECHNIQUES - CYLINDER BENDING TECHNIQUES - CONES BENDING TECHNIQUES - FLANGE RED-HOT BENDING SHORT PLATE SERIES OF MACHINE LIGHT SERIES OF MACHINE NOTES How to bend Step 1 Plate A manual on the select or use of the Hugh Smith Vertical Plate Bending Machine

Variations in the pressure of the punch roll on a horizontal rolling machine can lead to unpredictable stretching of the plate during rolling. This problem is increased if many passes of the plate through the machine are required. In the vertical machine, the mill scale on the plate falls to the floor away from the plate and is pressed into the surface. This is a particular advantage in hot bending.

In cold rolling, the mill scale on the inside of the plate tends to be rolled into the plate surface, causing surface damage and uneven rolling. It is difficult to remove. The vertical machine is particularly suitable for carrying out rectification work either straightening a plate or in the area of the longitudinal weld. It is easy to correct for hard spots in plates by locally pressing further.

These machines are not as suitable for local rectification work and rerounding hot well-forged items. The vertical machine has the power to bend the plate in one pass, which leads to fast floor-to-floor times. Although the rolling speed of these machines is fast, several passes are necessary, which can cause problems of work hardening the surface of the plate and causing unacceptable straightness of the axes.

The vertical machine, being a press, is extremely versatile, able to form conical work, box sections around the roller, plate straightening, bar bending, and plate flanging. It can thus take the place of two machines in many cases where it would not be fully utilized, producing complex work. Though some machines are fitted with only cone rolling attachments, these are of limited use on thick plates, and since these machines are not designed as presses, they may have to be substituted with special adaptors.

With specially adapted bending bars and roller formers, it is possible to produce spherical-shaped articles. It is easy to mount the machine on a concrete floor.

The vertical bending machine is easy to maintain, and the higher mechanical complexity leads to more specialized and expensive maintenance. It is possible to produce plates with varying curvature, such as those required for oval cross-section tubular components. This is not as easy on horizontal rolls. The design of the Vertical Bender allows the bending roll to be smaller in diameter for the same load capacity as horizontal rolls. This gives the machine the ability to form smaller diameter cylinders than an equivalent horizontal rolling machine.

Horizontal rolls, due to their design, have longer roll faces or require a larger diameter to have the same load-carrying capacity as a Vertical Bender. Examples of work done on various projects.

REVERSE BENDING BAR HEIGHT FOR GY LANCER REMOVAL PLATE BENDING CAPACITY OF THE RANGE MACHINES FROM TONNES TO TONNES All Sizes in Millimetres MACHINE FORCE MAXIMUM TONNES TONNES TONNES TONNES PLATE WIDTH STANDARD ROLLER DIAMETER  UNDER DIAMETERS WIDTH THICKNESS HEIGHT THICKNESS MINIMUM PLATE WIDTH FORCE MAXIMUM  PLATE REMOVAL Capacity Table:

The are based on steel equivalent

The Plate widths as specified

Interchangeable rollers

The minimum force

Due to the many factors

Separate individual tables of plate bending capacities

When using the force NOTE All data based on steel 25 Kg./mm2 maximum yield.

Introduction to the use of Vertical Bending Machines The machine operates by a progressive bending method. The plate passes through a small increment of 100 mm. The reciprocating beam gives the plate a set. Then the plate is advanced 100 mm for another cycle. Once the bending force is applied to the plates, it is not simultaneously, decreasing the tangential load. Especially when rolling heavy plates, high loading or bending effort is necessary for small diameters in minimal time. A characteristic feature of such rolls is that the operation slows down considerably when near-maximum capacity is being utilized.

The highest loading or tonnage requirement for bending complete circles is when presenting the extreme end of the plate. Theoretically, bending right to the edge is impossible, as it would require infinite force. In practice, a very small end flat is left on the plate if adequate hydraulic power can be brought to bear as close to the end of the plate as possible.

Due to the use of direct-acting hydraulic rams, the vertical bending machine has exceptional capacity and is, in fact, superior to other types. It should be noted that for accurate work, the extreme end should have an offset to ensure a small percentage of over and means costs and more manageable manufacture.

To obtain the best results from the machine, it is essential that the plate can move freely over the floor area, and roller skates are provided with each machine. These skates are designed to accommodate a maximum weight of 5 tonnes each and have a standard height of 75 mm from the floor level. The total height capacity of the machine is greater than the maximum plate width, and with the use of skates, the top of the plate and the underside of the top housing or the cycle can be easily cleared.

Typical roller skates are also available for heavier plates to suit plate preparation. It is necessary to emphasize the need for a perfectly leveled steel floor plate around the working area of the machine. Extra pads can be supplied to make up the desired effective diameter. These plates should be securely butted within mm on a 600 mm straight edge. The inner skates are supplied with a pair of upper collars to receive the flat bottom edge of the plate, but special profiled roller skates can be supplied to suit any welding profile required. The weight of the plate is supported on the shoulder of the preparation, thus protecting the rolls.

The control desk layout can be supplied as either fixed or portable.

Setting of bending bar centers: Correctly set-up bending bars are necessary for the machine's operation. You need to have enough space between them to ensure proper bending of the plate.

The preparation of the machine before bending: Make sure the floor area around the machine is perfectly leveled and that the machine is properly prepared for bending.

Feeding the plate through the machine: Describe how the plate is fed into the machine, and make sure that it goes through the process correctly.

Determining the diameter of the plate being bent: Explain how to measure the diameter of the plate being bent and adjust the machine accordingly.

Main feed: Explain the main feed process of the machine, including the various components involved.

Techniques Forming of plates into cylinders The plate is placed in the machine, and the first end is then upset, after which forming can proceed, followed by upsetting the second end. If desired, both ends of the plate can be upset in the machine before forming to a diameter. Upsetting the ends is done in manual mode; the machine is later switched to automatic mode, and the operator monitors the drum diameter using a curvemeter or template while the machine bends and feeds the plate automatically. The machine has sufficient force to form cylinders within the rated capacity in one pass, but the operator typically prefers to bend the plate to a slightly larger diameter on the first pass, using a second pass to bring it down to size. This approach allows for variations in plate thickness or yield.

Correction of overbent cylinders A special feature of the machine is the ease of correcting overbending or ovality. To correct local overbending, it's necessary to reverse the 3-point bending system using spacers and a nosebar, as shown, to press out the overbend. When the cylinder has been welded at the seam, as shown, higher power is required than before welding, which can be compensated if necessary by opening up the bending centers.

Bending Techniques Forming of plates into cones To create conical shapes, the machine requires proper support, especially when forming larger cones. The machine needs stable support with sufficient clearance underneath the bottom roll, so it's essential to ensure that one end of the plate is supported on a corresponding structure before each pressing stroke. The plate must rest properly on the supports before any pressing occurs. For cylinder forming, the plate feeds through the machine with incremental adjustments.

Flanging Techniques Flanging capacity for all widths of the machine The machine's force is given in tonnes, and the thickness is measured in millimeters. The machine can handle different material thicknesses. Note that the provided thickness values are for steel with a yield stress of 25 kg/mm².

Red Hot Plate Bending The vertical bending machine is suitable for bending plates hot, which can be necessary when dealing with pressure boiler work. This process increases the machine's thickness capacity and is particularly useful for bending small diameters as required for such work.

In general, hot bending roughly doubles the thickness capacity of a machine because the steel's effective yield point is reduced when the temperature reaches around 950°C. Red hot bending resistance increases as the square of the plate thickness.

The vertical plate bender offers several advantages over horizontal rolls when it comes to red-hot bending. These include better templating accuracy, reduced scale formation on the plates, and an effective cooling system.

In conclusion, most plate bending work can be done cold. Still, in specific circumstances, red-hot bending is required and is best performed on a vertical machine. The extra equipment needed is not overly expensive.

The Short Plate Series of Vertical Plate Bending Machines The Short Plate Series of Vertical Plate Bending Machines is designed to handle different sizes of plates and offers forces of up to 5C8 tonnes for plates up to 3750 mm in width.

The Light Series of Vertical Plate Bending Machines The Light Series of Vertical Plate Bending Machines comes in various sizes and offers forces of 3C4 and 5C8 tonnes for plates with capacities of up to 3750 mm drums.






The original leaflets are for sale. A preview is shown. The price of the leaflet is on request.