Ims ve ECCENTRIC PRESSES

lms ve ECCENTRIC PRESSES

Presses with SIX GUIDES

- MODEL: 50-RE - 63-RE - 80-RE - 100-RE
- Maximum pressure near bottom dead center: 50 Tons - 63 Tons - 80 Tons - 100 Tons
- Span between supports: 340 mm - 370 mm - 400 mm - 420 mm
- Distance between connecting rod axis and support (notch): 230 mm - 260 mm - 280 mm - 330 mm
- Ram size: width x depth: 430x340 mm - 450x360 mm - 560x376 mm - 580x390 mm
- Table size: width x depth: 700x450 mm - 800x500 mm - 850x550 mm - 950x650 mm
- Min. distance between table and ram down adjusted up: 300 mm - 330 mm - 360 mm - 400 mm
- Ram adjustment: 70 mm - 70 mm - 80 mm - 90 mm
- Adjustable ram stroke: 0-90 mm - 0-100 mm - 0-110 mm - 0-140 mm
- Ram hole diameter x length: 40x72 mm - 50x80 mm - 50x80 mm - 50x80 mm
- Strokes per minute: approx. 70 - 65 - 60 - 55
- Drive motor rating: 3 kW - 4 kW - 5.5 kW - 7.5 kW
- Approximate weight: 3000 Kg - 4800 Kg - 5400 Kg - 7000 Kg
- Air cushion adjustable pressure max.: 1:3 - 1:5 - 1:5 - 1:7
- Air cushion adjustable stroke max.: 45 mm - 55 mm - 55 mm - 70 mm
- Overall dimensions: 1295x700 mm - 1620x850 mm - 1635x855 mm - 1905x1000 mm

- Entirely made in welded and annealed steel panels to eliminate stress
- Robustly built to guarantee the minimum flection even when used at the maximum charge

• Selection can be done by key giving three operative cycles and can be controlled by buttons.
  - The direct action on the "clutch-brake" system allows the following cycles:
    - SINGLE: manual work.
    - REGULATIONS: dies regulation.
    - CONTINUOUS: automatic work.

- Built in forged, chromium-plated, and hardened steel.
- Stroke regulation can be obtained by an eccentric with frontal jaws, and the slide position is directly indicated.

- Built in welded and annealed steel equipped with six long guides and air counterbalance cylinders.
- Ram adjustment can be manual or motorized with an indicator of position.
- In the ram, a special hydraulic system to reset the ram position in case of overload is located (mod. R - RE).

- Flywheel driven by motor with V-belts is connected to the motor unit with very strong «clutch-brake» which has been designed to obtain a low inertia and consequently a good reduction of heat.
- Crankshafts and gears are in special forged steel of high quality and work in oil bath.

- Slide with six long guides
- Counterbalance cylinders for the slide (for models R-RE)
- Centralized lubrication system
- Air equipment with filter-lubricator, reduction units, pressure gauges, and air receivers
- Three-phase electric motor
- Electric equipment with braking angle control, push-buttons simultaneity, double solenoid valve, strokes counter, press-button, and control board
- Lubrication automatic pump
- Hydraulic release device (mod. R- RE)

- Air cushion
- Subsidiary table
- Hydraulic safety device
- Variable speed motor
- Two-polarity motor
- Removable drive station
- Feeder system
- Safety guards
- Semi-automatic and fully automatic stroke change

IMS - Industria Masetto Schio s.r.l. - recently acquired "Officine Meccaniche Dalle Molle s.r.l.", a company with over 40 years of experience in the power press market. Leveraging this extensive experience, IMS is now able to offer its loyal customers a comprehensive range of Eccentric Presses known for their outstanding quality, versatility, economy, and durability. The design of IMS machines combines simplicity and strength, ensuring accuracy, safety, and functionality even in the most challenging applications. With models ranging from 15 to 400 tons, including both fixed types (RE-R = gear drive, VE = flywheel drive) and inclined types (R1-V1 optional), IMS can meet the needs of even the most demanding customers.