Mep Shark 282 Sawing Machines

Mep Shark 282 Sawing Machines NC evo VERSION, FURTHER
FEATURES:
Shark 282 NC evo, CNC electrohydraullc automatic sawing machine, also working with semí-automatic, semi-automatic/dynamic and manual cycle (Refer to the paragraph
"CUTTING CYCLES')
9- CNC machine wíth controlled double axís so as to program, on thesame bar, і000 different lots each of different lengths and quantitíes.
- NEW protections for the operator safety.
ln polyester, with thermo-shaped buttons, wíth tactile feeling and sound signal when operating.
- NEW field bus control system (MODBUS protocol):
- Double microprocessor with serial

Band sawing machlne SHARK model 282, available ln fourversions:
MANUAL, manual wíth CCS, electrohydraulic SEM1-AUTOMATIC (SXI evo) and electro-hydraulic AUTOMATIC (NC evo), to cut from 45 ° right to 60° left.
For the explanation of the different working cycles refer to the paragraph
"CUTTING CVCLES ".
A FEW COMMON FEATURES:
- Blade-holding bow, více unit and base in sturdy cast íron.
1 - Precisíon grading etched on the cast iron structure.
- Electric system with totally ídentífable wiring and 24 V 1ow
voltage system.
-IP55 control handgrip to operate manual cycles.
 2 - Wide working surface with rotating plane installed on a roller
bearíng, dia. 265 mm, pre-loaded with thrust bearing.
3- Brush blade-cleaníng device.
4- Clamping unít slíding longitudinally to the right/left with fast approachíng více.
- Precisíon strokes adjusted for the cut o°, 45 °, 60° left and 45 ° right.
- Bimetal band 27x0.9 mm.
- Service keys and instructions manual, for maintenance and spare parts list.
MANUAL AND CCS VERS/0N5,
FURTHER FEATURES:
- SHARK 282 with manual mode working and - SHARK 282 CCS with
manual mode working + cut with autonomous head feeding bygravíty.
5/6 - CCS (Cut Control System) device, íncluding: (- A Switch for
cutting in manual or automatíc cycle -
Cutting speed adjuster- CHydraulic brake with tank - D Límítswítch for the band stop), that can be supplied also as optional kít to be ínstalled on already manufactured machines.
7- Hydraulíc transducer to display the band tensioning.
 8- Steel base with removable coolant tray and electríc pump for the band lubrícatíon and coolíng.
DESCRIPTI0N OF THE CUTTING CYCLES
- MANUAL cycle: the operator approaches the blade to the piece to be cut and he starts orstops the blade rotatlon by the "START" switch on the handle.
- MANUAL cycle wíth CCS: enables to make single cuts without operator using the
head weíght - sultabl y balanced - controlled by a hydraulíc brake to adjust the feedíng speed.
The operator approaches the band to the pіece to be cut and he starts the cycle by
the "START"swítch on the handle; after the cut, the bow ís manually lífted up to the wíshed posítíon.
- DYNAMIC SEMI-AUTOMATIC cycle: this system extends and símplífes the machine use modes; single píeces can be cut wíthout setting any parameter.
The operator approaches the band manually to the piece to be cut and pressing the "START" switch on the handle, the band rotates and the head goes automatically down. At the cycle end, the machíne stops and returns to the positíon where the "START" switch had been pressed; the operator can move the bow
to position it an another piece to be cut.
- CCS and dynamíc/semi-automatic cuttíng cycles so as to make odd cuts mindless of
previous program parameters.
- SEMI-AUTOMATIC cycle: Startíng the cycle: - the vice closes and the motor starts
- the head goes down to execute cut the motor stops - the head returns - the více
opens.
- The head stroke, according to the dimensions of the material which has to be cut, ís set directly from the control panel.
AUTOMATIC cycles:
- 1 single cycle; carries out this síngle cuttíng program for píeces of the same
length, stoppíng the cycle and gívíng a light and sound alarm to separate the
píeces cut ín that lot.
- 2 continuous cycle; carries out all cutting programs for dífferent length from the
same bar ín sequence.
- 3 fast programmíng; carríes out the cycle pragrammed dírectlyon the workíng vídeo
page.
- UTILITYSTEP; accessible from every cycle, makes the bar facíng cut, the fırst pіece
cut and then stops so that the piece can be measured.

SX1 evo VER510N, FURTHER FEATURES:
Shark 282 SXI evo, semi-automatic, electro-hydraulic sawing machine also
workíng wíth semi-automatic/dynamíc and manual cyc(e (refer to the
paragraph "CUTTING CVCLES').
- Machíne with latest generation MEP controller exclusively designed for
MEP semi-automatic sawing machínes.
- New console with all centralízed controls, installed on an articulated
arm to be easily moved in every operating position.
- Upon request, the machíne can be supplied with the vertical control
panel see picture on `ÁCCESSORIES')
- Low voltage soft keyboard, wíth thermo-shaped buttons, with tactíle
feelíng and sound signal when operatíng.
- Display to visualíze technologícal parameters, among which diagnostics
and alarm messages.
17 - Latest generatlon hydraulic control unit, with high efficiency and low energy consumption.
- Double band rotation speed (36/72 m/min) wíth possibility of installing,
even later, the electroníc ínverter for the continuous adjustment of the
band speed (from 15 to ıoo m/min).
13 - The head stroke, according to the dimensions of the material
which has to be cut, is set directly from the control panel.
14 - Manually-operated blade tensíoníng by electronic transducer to vísualize band tensíoning.
8- Steel base with removable coolant tray and electric pump for the
band lubrication and cooling.
- Preset to be equipped with the spray mist system (OPTIONAL), as well as
with the standard-delívered traditional lubrication with emulsíble oíls.
- Machine preset for being handled by transpallet.