Waterjet EDGE 5 4-axis

Waterjet EDGE 5 

4 axis technology intelligent taper control
The system compensates for the natural taper that is produced by the water jet while cutting. The enables the operator to enhance the squareness of the cut material, top to bottom, while allowing highest possible cutting feed rates. The water jet position is compensated up to 2 degrees, via the NC control of the motion system. This ensures a high quality part at low cost. During the compensation, the jet is also directed towards the piece in order to reduce the tail delay effect as well as the acceleration-deceleration ramp times around the corners, for faster and more economical cutting cycles.

ITC technology with 2D 5 axis bevel and touch probe sensor for accurate position calibration. Technology 
the 5 axis evolution 3D cutting system automatically maintains a constant distance between the nozzle and the material, through the use of a touch probe device. This is also done while the cutting head is rotating. The interpolation of the axis in any direction.
It is also possible to interpolate in 3D all axis simoultaneusly, monitoring the cut profile
with a laser pointer, integrated on to the cutting head.
TECHNICAL SPEClFICATION
lnnovative design, alluminium casting
PATENTED INFlNITE ROTATION system with 4 concentric swivels optional
High pressure water, air, abrasive, electrical
- Laser pointer for 2D and 3D vísual countouríng control
- 3D Cam Software wíth LT.C.TM (Intelligent Tapering ControlTM)
SPECIAL FEATURES
- lntegrated Touch Probe and anticollision System ,
Laser Pointer and Vacuum Assïst Sensor

The intensifier pump produces a water jet pressure up to 90,000 PSI. The water jet is pushed through a self-aligning cutting head managed by a NC control system: the water, ejected through a gauged orifice, at 4 times the speed of sound, can be mixed wíth abrasive in order to cut shapes in any material, up to a thíckness of 300 mm (12 inches).

ADVANTAGES
 Mach Speed íncrease from 3 to 4 of the supersonic Jet speed
 lncrease cutting power densíty by 83%
 Possíbility to cut materials with pure water only (no abrasive)
3 mm (1/8 ínch) = aluminum
1 mm (1/24 inch) = títaníum
 lncrease Max. cutting thickness
Títanium up to 10" = 250 mm
Steelup to 12" = 300 mm
Aluminum up to 16" = 400 mm
 lncreased cuttíng speeds:up to 250%
with identical abrasive mass flow rate
 Reduced abrasive consumptíon:
30% less
 Reduced kerf and higher cut quality, up to 3 times better with identical cutting speed (surface finish)
 Ability to cut harder materials such as ceramics

1) The Graphic-Window shows the shape of the work piece and
the cutting path. It can be used to define the start point for the restart function.
2) The Display-Bar shows Position, Tіme, Offset, Feedrates and Override data.
3) Operational Functions for the dífferent Modes (Jog, Manual, Automatic).
4) Main menu switches for the different Modes
5) Main Switch Board.
6) USB Port.
7) Overríde.
8) Teleassistance.

Sharp is a CAD/CAM solution designed to automate the programming of Waterjet machines.
Within thesameprogram environment, you can design or import a part by DXF , consult the plate warehouse, perform manual or automatic nesting, execute manual or automatic cutting sequences, generatethe NC program and calculate time and costs.
Expert Cut Plus allows youto easily configure and manage multi plates.
Lantek Expert Cut Plus provídes:
• Automatic lead-ins/lead-outs
• Water jet technology tables
• Speedreduction incorners
• Support of technological elements such as chamfers (bevels),loops and bridges
• True-shape nesting, including parts in parts

Lantek Flex 3D 5X is a full featured application for the automatic programming of 5 axis machines Waterjet technologies
Technical featuress
• Standardsolidsand surfaces supported formats:SAT, IGES,VDA, STEP, Parasolid
• Modules for supporting formats of Catia, Solidworks, Solid Edge,lnventor, NX And Proe
(CreoElements)
• Automatic detection of the partcuttingcontour andthickness
• Multiple possibilities to change head position ineach point
• Lead-ins,lead-outs and microjoints/tabs
• Simulationof completeworking environment: part, table,fixtures, head, etc.
• Collision check and automatic avoidanceof collisions automatically generatesthe fixtures necessary for positioning the part correctly on the machine table

Touch Probe Sensor with Anticollision, Laser Poínter, and Uacuum Assist
Pre-piercing and Counter sink device
Multiple Heads System
Automatic Sludge Removal Equipment with or without Submerge Cutting System
Wars: Semi automatíc abrasive removal System
1 Ton Automatíc Pressurized Abrasive Tank

Renishaw Laser Straightness inspection and verification
Ball Bar ínspection and verífication
Double Renishaw Laser inspection and verification of Positioning
Accuracy and Compensation

The Quality Control respects 1E0 9001-2008 and guarantees the CE mark for all components produced and for all complete equipment. A Fína1QC document and abench mark cutting test are always supplíed together with the machine to certify the accuracy and repeatibilíty tolerances really measured respect those guaranteed by the Factory

WaterService is an After Sa/es Service Center exclusively focused on Waterjet cutting technology, providing professional and competent technical support to all Waterjet users.
A customer oriented approach enables comprehensive technical assistance while guaranteeing maintenance services through highly skilled technicians.
The supply of genuine parts, components and accessories for
Waterjet cutting machines completes WaterService's range of services.
WaterServíces continuously expands its product range, with ever expanding inventory coupled with high quality services.
Services offered by our Customer Service Team include:
• Technical Assistance in and Out of Warranty
• Online Tele-Assistance
• Supply of Genuine Consumable and Spare Parts
• Complete Waterjet Machine Range Commissioning and Training
• CNC and Software Upgrades
• Preventíve Maintenance Contracts