Gurutzpe super bt 6 30 horizontal lathe

HORIZONTAL LATHE GURUTZPE MODEL SUPER-BT - MACHINE NUMBER: BETWEEN CENTERS THIS MANUAL IS DIRECTED TO THE PERSONNEL IN CHARGE OF TAKING CARE OF THE MACHINE. ATTENTION It is entirely necessary to read this instruction manual, carefully noting its contents, before putting the machine into operation. The purpose of the manual, besides supplying instructions and explanations for the cases given, is to give information on the mechanical group of the machine. By consultation for said end, the corresponding chapter and section. If faced with difficulties cannot be solved by the use of the manual, please get in touch with the factory. This instruction manual is of our property and we offer it only to the users of our machines. It contains drawings and technical prescriptions. It is not allowed to copy them neither totally nor partially, not even to give them to other people without our permission.

GOREKAN, S. A. Pol. Ind. Parcela T- ZESTOA-DEBA Apdo 78 20740 ZESTOA GUIPUZCOA SPAIN TEL. 943 0180 - FAX 943 VERIFICATION SHEETS GOREKAN, S. A. Pol. Ind. Parcela T-ZESTOA-DEBA Apdo 78 - 20740 ZESTOA GUIPUZCOA SPAIN HORIZONTAL LATHE, GURUTZPE, MODEL SUPER-BT 2-T INSTRUCTIONS MANUAL BOOK CHAPTER PAGE No. 1 SUPER-BT LATHE RECEPTION No. 1 HOW TO MOVE THE LIFT The machine is designed to be moved by means of two differential gears, every one of which supports the machine, a hook grasped to a bar, inserted in a hole, bored with this purpose in the machine. Check for any damage during shipment, and see whether the accessories are complete. If anything is wrong, contact the manufacturer at once. FOUNDATION LEVELING See drawing in fig. 1. We recommend particularly this bolting anchorage, as being proved by experience. Once the machine is situated in place, it will be leveled with the screws located at the base with this purpose. To do this a centesimal level must be used. The leveling screws will rest on iron washers so that specific pressure on the floor does not exceed its strength. Such washers will be fixed by concrete to prevent any motion. During leveling, the screws so designed must rest on their corresponding washers. This operation must be carefully performed. After leveling, the machine will be fastened with the bolts so provided, which are the holes bored beside the leveling screws. Leveling will be checked during the operation. The tests made at the manufacturer's and which appear in the standard sheet, must be checked before operation. They must comply with the mentioned standards. Once all these operations are performed, the machine must be cleaned. CNC LATHE 7765 CHAPTER N 1 OBJECT PLACED NO. SPUETHOPP CHAPTER PAGE SUPER-BT LATHE ELECTRICS No. 1-2 are enclosed in an electric cabinet. The Control voltage protected with that if the power united in motor is Y SUPER-BT LATHE HEADSTOCK ASSEMBLY No. That axle 10 rotates front section on a double precession - boring Ø.S. As for its rear section, it rests on a cylindrical roller bearings precision P5. To adjust the one roller bearings, do as follows: Drive nut 107and 108 in the required space. Do this with the gear lever in neutral position. ODD: LOCK CENTRIC Centering is achieved by means of two hexagonal screws 170 shown in the lyre section, located in the front part of the head. Reduce previously the pressure of the headstock fixing screws. To do this, take out the plate. LUBRICATION AND OIL REFILLING Lubrication is achieved by means of the tray distribution, through a constant discharge by the pressure. General Instructions in Chapter 1 in General Lubrication. SAE-10 or similar oil is recommended. To empty the headstock oil content, take out the lyre and the stopper located in the headstock guide. To refill, pour it after removing the two covers at the top of the headstock. During declutching, a hydraulic brake stops automatically the main axle motion. CHAPTER SUPER-BT LATHE AVAILABLE POWER AT THE MAIN SPINDLE TABLE High-speed range Low-speed range MATERIAL TO CHARACTERISTICS WORK Carbon Steel Alloy and others 100 125 380 Manganese Steel 2 up to 100 G Malleable up to Hardened Casting Bronze Brass Aluminium Re Specific cutting strength CHAPTER PAGE No. 2 SUPER-OT LATHE AVAILABLE POWER AT THE MAIN SPINDLE TABLE TABLE Chip MATERIAL THICKNESS mm. Normal High-speed steel 125 FACTOR A- 16 2 5 super-high speed Salt 51 Tungsten carbide 0.80 FACTOR A Depends on chip FACTOR B- Depends on cutting thickness speed TYPES OF WORK C Turning with normal tool 1 Turning with constant profile 125 FACTOR C- According to the type of work.Revolution per minute mm2. chip section. Po a Pressure at - bit = Torque available edge, Ln For this type of the main axle, in k rn. of machine, Pc must K8. Available power at the - Pe - Fitting Factors to select