Hurco autobend p2 control system

Hurco Autobend P2 Plate Gauge Power Press Brake Gauging Systems From Hurco. 1978 Hurco Manufacturing Company, Inc. All rights reserved.

Autobend P2 Plate Gauge support devices to support the sheet at the rear of the machine and thus accurately gauge the typically longer Autobend P2 plate gauges are specifically designed for dimensions that are often encountered in plate forming.

Forming parts of light plate that do not exceed 600 pounds in weight. The gauges may be installed on mechanical or hydraulic press brakes from 10 to 18 feet long. The P2 system features a closed-loop DC servo drive, which maintains accurate positioning at all times. It also acts as a shock absorber during handling, which usually involves two operators assisted by some material handling device. The P2 system can be equipped with Hurco's Autobend 1V single-axis control or the highly advanced Autobend 1V two-axis control, giving the user of large press brakes the same flexibility available on small press brakes.

P2 systems feature extremely rugged, cast steel, twin drive gauge arms that are bolted to the rear of the press brake bed. Because these units are specifically designed for heavy press brake forming, they have an increased gauging range of 36 or 48, plus oversized vertical supports that provide additional vertical and horizontal adjustments. The twin drive design is especially effective in heavy forming, as some parts may occasionally need to extend below the dies and between the gauges during the forming operation. In addition, this allows the use of roller conveyors or other material.

General Specifications: Four hardened and ground gauge fingers are furnished with brackets for facilitating quick clamping along the continuous gauge bar. These fingers, which project 6 inches away from the main gauge surface, are suitable for forming narrow flange work and parts that do not adapt to being positioned against a continuous gauge surface. The control panel is housed in a heavy metal enclosure with a pendant-type support arm for convenient positioning. The support arm can be bolted to either end of the press brake on the side housings. Data is entered manually through the keyboard, with the display of station in use, programmed gauge dimension, and bend allowance. Keylock switch provides dimensioning in either inch or metric units. Up to 250 gauge positions stations may be programmed at one time. Control has solid-state logic and memory. Self-recharging battery system retains program in memory, up to 3 months, in the event of power failure. Two self-contained gauge housings are supplied for use in the rear of the press brake. The long dimension projects away from the press brake where each housing is bolted on the rear of the bed. The carriages operate on continuously supported hardened and ground ways. The carriages are positioned by motor-driven hardened lead screws with two recirculating ball nuts to avoid backlash. The motors are driven by current featuring a closed-loop servo drive. The gauge bar can be positioned from 0 to 36 inches or 0 to 48 inches from the centerline of the forming tools. The standard gauge bar is 9 feet 6 inches long and has 12 inches vertical adjustment. The P2 is designed to form parts of a nominal plate or other parts that do not exceed 600 lbs in weight. Gauge housing weight is approximately 225 lbs with the long dimension projecting away from the press brake bed.

The travels at and make a move in seconds, including and.

Service Required volt, single phase cycle with capacity.

Warranty Factory will replace any defective parts during one year after shipment of system.

Installation Installation by customer and Hurco service engineer. Gauges shipped direct to customer for basic mounting of components and power source to control box. Hurco service engineer assists in final hookup. The tilting is furnished with removable wear performs installation check-out, trains customer personnel strips on a machined face and is fastened on two in operation of system. Complete owner's manuals furnished.

P2 Plate General Specification - Model Preset Projection of Accuracy Speed Number Travel from Brake Bed P2-36R repeatability P2-48R positíoning 

repeatability 

Standard Components for Model P2 Optional Features MDs Multiple Depth Stop Option synchronize manually preset depth settings with positions for hydraulic press brakes using electrical or electronic limit switches for ram reversal at bottom of stroke and ram stopping at top of stroke. Customer must equip press brake with multiple depth stop or electronic limit switches.

Tape Cassette Option This option provides the flexibility of having all parts programs stored on mini tape cassettes, eliminating the need to manually re-program parts for each production. Each mini tape cassette will store 500 stations or 120 parts. This option includes the addition of the read/write head to the pendant controller and the expanded memory capacity.

Autobend Two Axis Option Provides a means for programming the desired bend angle and clearance on top of the work for each station. Special entry keys provided. For most hydraulic press brakes. For full details, refer to Hurco two-axis control spec sheet.

Control panel with pendant mounting support arm. Two reference bars. Power supply, micro-processor control, and servo amplifier. Hurco Manufacturing Company, Inc.

Hurco Box Patents Foreign patents applied for. Guion Road Indianapolis, Indiana HSF252